Home Made Rapid Fire Mod VS The Intensafire Mod

by Xbox360mods.ca Latest Xbox 360 News! on May 13th, 2010

filed under Uncategorized

The home made xbox 360 rapid fire mod vs. the new intensafire mod. See which one is better for your xbox 360 wireless controller. Huge difference in performance and quality.

 newbannerxbox360mods

XBOX 360 CONTROLLER HOME MADE MOD!

 VS

SIMPLE XBOX 360 RAPID FIRE MOD!

 

step 1: WHAT YOU WILL NEED 
First off you will need, A TT9 Torx Driver A Small Push Button Rapid Fire Switch Some Thin Wire, Such as IDE Cable A Wireless Xbox 360 Controller. Soldering Equipment A Drill and a drill bit to match the diameter of the thread on your switch. Don’t forget a surface to work on. I would suggest near the computer just in case you forget where the wires need to be soldered to.  

Step 2: DISMANTLE WIRELESS CONTROLLER!
Taking the battery out will reveal the hidden screw underneath the sticker. There are 7 screws to remove, so grab thatTT9 Torx driver and twist Anti -Clock-wise) With the buttons facing down. I recommend taping the buttons to the body on the outside so the buttons do not fall out. Separate the two halves carefully, paying attention to the rumble motors. 
 
step 3: DRILL HOLE FOR RAPID FIRE SWITCH!
 Find the best place to put your switch, choose very carefully, as once you’ve drilled, its staying on your $50 Controller! Once you have found the right place, place the two halves back together and see if there is enough room for your switch to go in. If there is, well done. Remove the board so that it doesn’t get damaged, then put the bit in your drill and carefully drill a hole. In most cases you will have to disconnect one of the rumble motors in order to install the switch. Most buttons or switches WILL NOT fit without the permanent removal of one of the left or right rumble motor.
 
step 4: FIT SWITCH.
Place the switch in your new drilled hole. Make sure that you orient the pins so that they are not getting bent or squashed when the controller is back together. I recommend if you are to remove one of the rumble motors, remove the smaller one. Just remember you will only have the sensation on one side of the controller.
 
step 5: SOLDERING WIRES.
Heat up the soldering iron, not too hot or else it might melt some components. Be sure to have a steady hand when soldering the wires to the contact points and try not to touch the board for too long as you might melt the circuit board. Make sure wiring runs stay clear of the black button pads, analogue stick, and any other area where the buttons may be blocked by the wires.
 
step 6: REASSEMBLE CONTROLLER
Check to make sure the switch pins are not going to make contact with anything on the other half of the controller when reassembled? Are all of the wires free from places of movement or screw holes? Are the solder joints correct and not dry? Are all of the annoying black pieces of the controller back on their positioning pins? Here comes the moment of truth, Install the battery and test to see if the Rapid Fire Mod switch is working.

Well I don’t know about you but having done a homebrew rapid fire mod switch was definately nerve racking and hard. The soldering of the wires to the board seemed almost impossible and nearly melted the board several times. Unless you purchase a heat controlled soldering gun you might want to consider another alternative to modding your wireless controller.

The most annoying fact is You Have To remove one of the rumble motors in order to install a switch for the rapid fire. With several different switches I have found and have tried there is no getting around removing one of the rumble motors. Having one of the rumble motors was acceptable untill game time came and the controller would only vibrate on one side making it feel awkward but tollerable.

ALTERNATIVE

 

BEST AND MOST SIMPLE RAPID FIRE MOD FOR ANY WIRELESS XBOX 360 CONTROLLER!

HERE IS WHAT YOU GET IN THE COMPLETE KIT! Dual rapid-fire. 5-mode Rapidfire settings. Easy 3-minute installation process! No soldering or wires required! Can be used in all XBOX 360 games. Mode button for advanced modification. Easy installation with video instructions. Customizable user-programmable modes. Works in all wireless Xbox 360 controllers. Does not require a more powerful battery. Includes screwdriver and conductive glue for quick installation, no additional tools required!

What does it do?

The best and most simple Xbox 360 rapid fire mod, INTENSAFIRE modifies XBOX 360 controllers (CG, Matrix and wireless), allowing them to control 5-mode rapidfire settings, and use customizable user programmable modes. It uses the existing Sync button to toggle modes, and on and off. It also enables dual rapid-fire- usable in all XBOX 360 games, including gamer favorites: Left 4 Dead, the Call of Duty series, the Halo series, the Gears of War series, and Street Fighter.

How is it better?

5-mode sleeper mod kits exist. Dual rapid-fire mod kits exist. The INTENSAFIRE mod kit has both. There are controllers on the market, prefabricated, that do what this rapid fire mod offers, however other controller mods are going for well over $60. We offer a mod kit that is extremely simple to install, taking no more than 3 minutes with tools included, for less than 1/4th the cost of the prefabricated units. Other mod kits require drilling, wiring, gluing, and crazy wiring of your controllers. This Rapid Fire Kit only needs a few existing points to connect to the controller board. Just attach the INTENSAFIRE flex board to the controller, use the included soldering paste and you’re ready to go in no time!

SEE OUR INSTALLATION VIDEO HERE!

WATCH OUR RAPID FIRE MOD IN ACTION HERE!

The Intensafire rapid fire mod Works for such Games as: Battlefield Bad Company 2, Call of Duty Modern Warfare 2, Halo Series Aliens vs Predator, Army of 2 The 40th Day and many more Great First Person Shooter Games. I AM SURE YOU HAVE LOOKED ON YOUTUBE TO SEE HOW A CONTROLLER MOD IS DONE! WE ALL HAVE!

GO AHEAD! FOLLOW THE CRAZY KIDS DIRECTIONS ON YOUTUBE.

IF YOU DARE!

GET THE BEST RAPID FIRE MOD NOW!

DOMINATE ALL FIRST PERSON SHOOTER GAMES!

INCREASE YOUR GAMER SCORE & UNLOCK ACHIEVEMENTS!

GET A RAPID FIRE MOD FOR YOUR CONTROLLER AND SMOKE’EM ALL!

LOWEST PRICE ANYWHERE! ONLY $21.97 + NO TAX

 

GET THE BEST RAPID FIRE MOD FOR XBOX 360 CONTROLLERS HERE!

WE SHIP WORLDWIDE! & FAST DELIVERY TIME!

WHEN YOU PLACE YOUR ORDER TODAY YOU CAN PAY BY!

International payment methods:

- Visa credit card with SSL – Paypal – Eurocard/Mastercard credit card with SSL – American Express credit card with SSL – Visa credit card with SET – Eurocard/Mastercard credit card with SET – Diners credit card with SSL – JCB credit card with SSL – Money Order/International Money Order – Western Union – Bank Transfer

WHAT IF I HAVE: NO CREDIT CARD! NO PAYPAL! NO PROBLEM! Other US & Canada payment methods: - Cash On Delivery (COD)

GET THE BEST XBOX 360 RAPID FIRE MOD HERE AT : XBOX360MODS.CA

213 Responses to “Home Made Rapid Fire Mod VS The Intensafire Mod”

  1. Isela says:

    I wanted to with thanks for this fantastic read!! I definitely enjoying every little bit of it.I have you saved as a favorite to check out new stuff you blog post. Yours trully, Isela.

  2. Hey cool post, I enjoy reading your blogs, and lookforward to seeing more great posts from you.

  3. Excellent post I must say.. Simple but yet interesting and engaging.. Keep up the awesome work!

  4. I’d like to say I could take the time to make my own rapid fire mod but I’m not all that handy :) . So I think I’ll just buy the Intensafire. That way I’ll have more time to play rather then spending it on making the mod.

  5. LED Lighting says:

    Hi Site owner. I truly like the posting and also your current internet site all in all! The post is extremely clearly written and also simply understandable. The WP theme is amazing as well! Would be good to know exactly where My partner and i are able get this. Please maintain up the great work. We require a lot more such website owners just like you online and much less spammers. Fantastic friend!

  6. Interesting thoughts here. I appreciate you taking the time to share them with us all. It’s people like you that make my day :)

  7. Pretty nice post. I just stumbled upon your blog and wanted to say that I have really enjoyed browsing your blog posts. In any case I’ll be subscribing to your feed and I hope you write again soon!

  8. I’m going crazy over here. yesterday I had a discussion about this same subject with my father and he wouldn’t believe me. With your site I can prove him I’m wright and he’s wrong! Thanx!

  9. teach dj says:

    Just wanted to say this Blog is in my rss you got a way with words.. Cheers,

  10. autto says:

    Hello…

    Nice share. I think your blog should come up much higher in the search results than where it is showing up right now….

  11. Got a call says:

    As a daily web surfer, I¡¯m always searching online for websites that can help me. Thank you

  12. I like it! Greetings! Things you brought up a lot of sense.

  13. How-to says:

    There is obviously far more to know about it as I expected. I like to stress that you have made some good points in your posting.

Leave a Reply